In most cases only the pitch axis is of interest to tilt the camera down or up. To frame the shots even better, the remote can be used to control the pitch and roll of the camera. You can change the com port in the advanced settings using the device manager. Note: Com port must be 1-10 of the UI does not work. You should now be able to connect with the 0.49 GUI and start tuning. 2) load the gimbal software in the Arduino environment 3) ensure your configuration is correct: - in Tools / Serial Port, be sure your USB port is selected - in Tools / Board, Arduino Pro or Pro Mini (5V, 16MHz) w/ ATMega328 4) Upload (arrow icon in toolbar) If everything works, you will get a message regarding memory size and a message that the new firmware has been uploaded. These instructions seem to be very thorough and worked perfectly on my Windows 7 PC: Required software To build the software, you need two things: - Arduino software environment: - Brushless Gimbal software: Build and install Building and downloading the firmware is pretty straightforward: 1) install the Arduino programming environment. Do not plug in the board without having downloaded the correct driver and then disconnect from the internet. The auto-detection will install an incorrect driver that is hard to uninstall. Windows: You are entering a world of pain. But now we need to re-tune the PIDs.īelow is the process for upgrading to 0.49: Drivers MAC: You are in luck! It seem like the correct driver is present without any additional action. The installed firmware is 0.48, however we could not get that version to talk to the 0.48 GUI. Mark managed to install 0.49 and that version talks to the GUI. I got my controller board to work out of the box without a firmware upgrade. Other people have stuffed them with earplugs ) Step 12: Software Setup. I filled them with silicon to stiffen them up. The vibration grommets are too soft for the weight of the GoPro. It needed a M3 screw that is just a bit longer. The upper mounting point can be screwed directly to the bottom of the TBS Discovery frame at an existing mounting point. Without the controller board stack there seems to be just enough clearance. I bought the leg extensions to give me enough clearance for the Gimbal. My airframe of choice at the moment is the TBS Discovery. Later you can cover the soldered connections with hot glue for physical strength and to insulate the wires. Note that since this is a three-phase motor, the order of the wires doesn't matter. If it takes more than a second you're doing it wrong. Put each wire on the corresponding solder pad, and touch the wire with the soldering iron, attaching the wire. Snip the wires and re-tin them with a generous portion of solder. Also it might give you enough pointers to design and build your own gimbal from scratch. This Instructable is meant to fill this gap. Hence building it can be quite a challenge. Also there were some incorrectly machined parts. Unfortunately that gimbal comes zero, zilch, nada instructions. The cheapest of all BLGs on the market today (and readily available) is the GoPro BLG and Controller (Martinez v1) from RcTimer. Instead of servo motors, a BLG uses re-wound Brushless RC motors in a direct drive configuration. Good gimbals are very expensive, cheap ones are not smooth.īrussless Gimbals (BLG) to the rescue! In there recent months there has been a flurry of activity around this new way of building camera gimbals. ![]() Reply by on Septemat 7:56am.Įvery self-respecting drone used for aerial photography needs a gimbal. this only works in Safe Mode, as the installer will warn you if you are not in Safe Mode. Guest Additions installer will ask you if you want WDDM, click 'No'. install Guest Additions and Basic 3D support.Īs opposed to experimental WDDM drivers. insert Guest Additions disc from VirtualBox Devices menu. Has anyone done this in VirtualBox? Has anyone seen these symptoms? 3D was the problem, but it wasn't as simple as enabling 3D support in VirtualBox. I got the gimbal from a local hobby shop, so it's not ready to roll with my Y6 like the ones direct from 3DR are. I got the application, along with drivers for the Tarot USB dongle, from here: I can see the 'Prolific' device in Device Manager, but when I get to step 3 at the above link: Double click on the ZYX-BMGC-ENV1.5.exe file (found in the above zip) and the configuration UI shown below should appear the application crashes every time. Windows XP, no SPs Each time I get a dialog from Windows telling me the application has crashed and asking about sending an error report. I would really like to be able to point my camera somewhere other than straight ahead, but until I get this app working, I can't do that. Windows 7, running the.exe in WinXP compatibility mode. I've been trying to get the Tarot T-2D configuration application to run for a couple of weeks in a VM with no luck.
0 Comments
Leave a Reply. |